3D打印机 Ramps 1.4LCD12864显示器模块 蓝底白字支持TF卡 中文屏

3D打印机 Ramps 1.4LCD12864显示器模块

兼容Ramps 1.4主控板

蓝底白字

支持TF卡

宝贝展示:

宝贝背面:

安装尺寸:

中文显示:

与主板的连接:

与Ramps 1.4的链接:

该屏幕在Marlin固件中的使用说明:

Marlin固件中基本配置在Configuration.h文件中,在Configuration.h中找到如下代码,在文件末尾的

屏幕和SD卡配置:

//LCD and SD support

//#define ULTRA_LCD  //general lcd support, also 16x2
//#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
#define SDSUPPORT // Enable SD Card Support in Hardware Console去掉前面注释开启SD卡支持
//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
//#define ULTIMAKERCONTROLLER //as available from the ultimaker online store.
//#define ULTIPANEL  //the ultipanel as on thingiverse
//#define LCD_FEEDBACK_FREQUENCY_HZ (咨询特价) // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
 
// The RepRapDiscount Smart Controller (white PCB)
// http://pic.lshou.com/pic/reprap.org/wiki/RepRapDiscount_Smart_Controller
//#define REPRAP_DISCOUNT_SMART_CONTROLLER 
 
// The GADGETS3D G3D LCD/SD Controller (blue PCB)
// http://pic.lshou.com/pic/reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
//#define G3D_PANEL
 
// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)
// http://pic.lshou.com/pic/reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://pic.lshou.com/pic/code.google.com/p/u8glib/wiki/u8glib
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER//这句话对应打开LCD2004屏幕支持,去掉前面注释即可。
 
// The RepRapWorld REPRAPWORLD_KEYPAD v1.1
// http://pic.lshou.com/pic/reprapworld.com/@products_details&products_id=202&cPath=1591_(咨询特价)
//#define REPRAPWORLD_KEYPAD
//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click
 
// The Elefu RA Board Control Panel
// http://pic.lshou.com/pic/www.elefu.com/index.php@route=product/product&product_id=53
// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARUDINO library folder: http://pic.lshou.com/pic/github.com/kiyoshigawa/LiquidCrystal_I2C

 

//#define RA_CONTROL_PANEL
 
热门商品